top of page

Dishwasher Cleaning in Toronto: Filters, Door Seals and Why Pre-Rinsing Backfires

Writer: Desmond Breau
Desmond Breau
Nov 9
25 min read

Of every appliance in a Toronto kitchen, the dishwasher is the only one most people assume cleans itself. It runs hot. It runs full of detergent. It finishes with a drying cycle. The reasonable conclusion is that anything which spends an hour inside that environment comes out clean, and that the inside of the machine is the cleanest surface in the room.

Two things make that wrong, and both of them are documented rather than anecdotal. The first is a peer-reviewed survey of thirty domestic dishwashers which found fungi in twenty-five of them and identified one specific component as the most heavily colonized part of the appliance. The second is that the two manufacturer use-and-care manuals consulted for this article both devote more instruction to cleaning the dishwasher than to loading it, and in both, the first maintenance task listed is to take out the filter.

There is a local layer on top of that. Toronto tap water averaged 119 mg/L of hardness in 2025, which puts it in the medium-hard band: not hard enough to need a water softener, but comfortably hard enough to put scale on a spray arm nozzle, film on a drinking glass, and calcium deposits on a filter screen. That number turns out to decide several of the choices below, including how often the filter has to come out.

Open and empty dishwasher in a sunlit modern Toronto kitchen, ready for a cleaning cycle

Why a Dishwasher Needs Cleaning at All

In 2016, researchers published a survey of thirty residential dishwashers across seven European cities, swabbing nine user-accessible interior sites in each machine. Fungi turned up in twenty-five of the thirty. The dominant group was black yeasts, chiefly a species called Exophiala dermatitidis, and the place they were concentrated was not the tub, the racks or the detergent compartment. It was the rubber seals.

The breakdown by site is the part worth remembering. Fungi were present on the rubber seals in 57% of the machines, on the side nozzles in 50%, on the doors in 47% and in the drains in 43%. On the seals specifically, black yeasts were the main contaminant in 40% of the dishwashers, and counts there reached as high as a million colony-forming units per square centimetre. Exophiala dermatitidis itself was recovered from 47% of the machines somewhere inside.

The comparative finding is the one that closes the argument. The same researchers sampled kitchens with and without a dishwasher. Exophiala dermatitidis was common in the kitchens that had one, and was found in only one of the fourteen kitchens that did not. Their conclusion was that a dishwasher acts as a reservoir which releases these organisms slowly into the room around it.

Proportion matters when reading that. The word the researchers use is opportunistic, and it is doing real work: these are organisms that mostly matter to people whose immune defences are already compromised, and the paper describes a reservoir rather than an outbreak. Nobody needs to be alarmed about a dishwasher. But the structural point stands on its own, and it is the reason this article exists: the machine concentrates organisms rather than eliminating them, and it concentrates them in one predictable place.

Why the seal and not the tub

The tub is sprayed at temperature with detergent several times a week. It is, genuinely, close to self-cleaning. The door seal is not, for three reasons that compound. It sits at the edge of the spray pattern rather than in it, so the water that reaches it arrives cooled and diluted. It is a fold, so it holds a thin reservoir of water and trapped food debris after every cycle. And it stays warm and damp in a closed, dark cabinet for hours afterwards.

A dishwasher, in other words, has one component that is permanently wet, permanently warm, never scrubbed and made of flexible material with a crease in it. That is a description of the ideal habitat, and it is also a description of the part that takes about twenty seconds to wipe.

A Dishwasher Does Not Sanitize Unless You Ask It To

There is a standard for this, and almost nobody outside the appliance trade has read it. NSF/ANSI 184 is the sanitization standard for residential dishwashers. To carry the certification, a machine must achieve a minimum 99.999% reduction of bacteria, which is what a five-log reduction means, and it must reach a final rinse temperature of 150°F.

Then comes the sentence that reframes the whole appliance. Sanitization performance is verified only when the unit is operated on its sanitizing cycle. A certified dishwasher is not a dishwasher that sanitizes; it is a dishwasher that can sanitize, on one cycle, which most households never select.

The manuals are consistent with that. In the Whirlpool instructions, the option is called Sani Rinse, and it sanitizes in accordance with NSF/ANSI 184 by raising the main wash to 135°F (57°C) and the final rinse to 156°F (69°C). A Sanitized indicator lights when it worked. It flashes if the cycle was interrupted or if the water never reached the required temperature, which is a quiet admission that the outcome is not guaranteed by pressing the button. The manual is explicit that only the sanitizing cycles are designed to meet the standard and that not every cycle is intended to. The Bosch manual describes its Sanitize option in the same terms: it raises and holds the temperature for longer to improve hygiene, at the cost of a longer run time and more energy.

Both manuals also note the limit of the certification. In Whirlpool's wording, certified residential dishwashers are not intended for licensed food establishments, which is a useful reminder of the scale of claim being made.

What this means for raw-meat days

Health Canada treats washing and sanitizing as two separate operations, and the distinction lines up exactly with the cycle question. Its guidance says that plates and utensils which have touched raw food should be washed in the dishwasher or in warm, soapy water. The dishwasher is listed as a way of washing. For sanitizing surfaces, the guidance describes something different: a kitchen sanitizer used according to its directions, or a bleach solution made up as 5 mL of household bleach to 750 mL of water, kept in a labelled spray bottle and rinsed off with water afterwards.

That second procedure is for counters, sinks and cutting boards. It is not for the inside of a dishwasher, and the reason is in the next section but one: both manuals prohibit chlorine near the machine. The two pieces of advice are not in conflict; they apply to different surfaces, and conflating them is how people end up pouring bleach into an appliance that forbids it.

Health Canada notes that children aged five and under are at increased risk of food poisoning, partly because their immune systems are still developing and partly because they produce less of the stomach acid that kills harmful bacteria. In a household with a toddler, the sanitizing cycle stops being an obscure setting and becomes the obvious default for the load that held raw chicken.

The Filter Is the Part Nobody Knows About

Older dishwashers ground food waste with a hard food disposer. Most modern ones filter it instead, which is quieter and more efficient and has one consequence the industry has never advertised well: the filter is a user-serviceable part that needs cleaning by hand. There are households in Toronto running a dishwasher daily that have never had the filter out, and in a great many of them the answer to why does it not clean properly any more is sitting at the bottom of the tub under the lower rack.

Where it is and how it comes out

On the Whirlpool layout, the filter assembly sits in the floor of the tub. Turn the upper filter assembly a quarter turn counterclockwise and lift it out, then gently pull the upper assembly apart. Rinse the pieces under running water until most of the soil is gone, using a soft brush if calcium deposits have built up. To reinstall, seat the lower filter under its locating tabs, insert the upper assembly and turn it clockwise until it locks. The manual gives a useful test for whether you have done it right: an unlocked upper filter turns freely.

The Bosch filtration system comes apart in a similar order with one more piece. Turn the coarse filter counterclockwise to release the system, pull out the micro filter, then press the locking catches and lift out the coarse filter. Rinse the elements under running water and clear the debris that collects between the coarse and the fine filter, which is the part people miss. Reassemble, reinsert and turn the coarse filter clockwise until the arrow markings align.

Neither procedure needs a tool and neither takes longer than two or three minutes once you have done it once.

How often, and the schedule nobody publishes

The Whirlpool manual contains something no cleaning article carries: a filter-cleaning frequency table keyed to two variables at once, how many loads you run a week and how you prepare the dishes before loading them.

Eight to twelve loads a week. Every two months if you only scrape the plates. Every four months if you scrape and rinse. Once a year if you wash the dishes before loading them.

Four to seven loads a week. Every four months if you only scrape. Once a year if you scrape and rinse, or if you wash before loading.

One to three loads a week. Twice a year if you only scrape. Once a year otherwise.

Two overrides sit alongside the table. Clean the filters sooner than scheduled if there is visible soil on the upper filter or if the dishes come out feeling gritty, which is the symptom most people notice first and attribute to the detergent. And the same manual, in two other places, simply says to clean both filters monthly, once in a general maintenance note and once in its hard-water guidance.

That is a genuine internal disagreement in one document, and the variable that resolves it is water hardness rather than load count. On medium-hard Toronto water, monthly is the figure to follow. The Bosch manual is blunter still and asks you to check the filters for debris after every cycle, which takes a glance rather than a disassembly.

What not to use on it

The one prohibition is specific and worth respecting, because the filter is a fine mesh screen and the damage is not reversible. In Whirlpool's wording: do not use wire brushes, scouring pads, or similar, as they may damage the filters. A soft brush for calcium and running water for everything else. A torn filter passes debris straight to the pump, which is a considerably more expensive problem than a dirty screen.

The Door Seal Is Where the Problem Actually Lives

Given what the research found, the seal deserves its own place in the routine rather than a mention at the end of one. The method is almost disappointingly simple. The Bosch manual asks you to wipe the door seals, the front and the control panel with a damp cloth and a little dishwashing liquid. That is the whole instruction, and it is the step that nearly every dishwasher-cleaning routine in circulation omits in favour of pouring something into the tub.

Technique is the only part that needs saying. The seal is a fold, so wiping the face of it accomplishes very little. Put a fingertip inside a damp cloth and run it along the inside of the crease around the entire perimeter, paying attention to the bottom edge where water pools and to the two bottom corners where the gasket changes direction. Then dry it. A seal left damp after cleaning is a seal you have just rinsed rather than cleaned.

What must never go on it

The prohibition list in the Bosch manual is longer than its cleaning method, and it rules out most of what gets recommended online. Do not use harsh chemicals such as bleach-based products to clean your dishwasher. Never use detergents containing chlorine. Do not use steam cleaners or high-pressure cleaners on the appliance. And so as not to scratch the finish, do not use sponges with a rough surface or abrasive cleaning agents.

Two of those are about the rubber specifically. Chlorine attacks flexible gasket material, and a gasket that has gone hard or has started to craze no longer seals, which turns a cosmetic decision into a leak. The abrasive rule covers the door itself, and there is one more clause for modern finishes: stainless steel polish must not be used on an anti-fingerprint finish or a black stainless finish.

That last point applies to the whole run of appliances rather than the dishwasher alone, and the material question is the same on every one of them. We have gone through it in detail in our guide to stainless steel appliance cleaning in Toronto, including grain direction and why water spots behave differently from rust.

The gasket problem is not unique to dishwashers either. The door seal on a refrigerator has the same geometry and the same tendency to grow things in the fold, with the added twist that on a fridge a dirty gasket is also a temperature problem. That is covered in our article on fridge cleaning in Toronto, and the cleaning technique transfers directly from one appliance to the other.

One more habit from the Bosch manual belongs here, because it is a seal and odour measure at the same time: during long periods when the dishwasher is not in use, leave the door slightly ajar. A closed, damp, warm cabinet is the condition the research described. An open door removes two of those three variables for free.

Why Pre-Rinsing Dishes Backfires

Overhead view of an adult loading dishes into a dishwasher in a home kitchen without pre-rinsing them

Rinsing plates before they go in is probably the most widespread piece of dishwasher folklore there is, and both manuals tell you not to do it. The Bosch instruction is direct: only remove large remnants of food, and do not pre-rinse dishware. It adds a resource argument, asking you not to pre-rinse under running water, and then gives the mechanical reason, which is the interesting one.

Modern dishwashers measure the soil in the water and choose a cycle to match. Pre-rinsing too intensively can cause those sensors to select a lighter cycle, which then leaves the stubborn residue behind. The machine is not being stupid; it is responding accurately to the evidence you gave it. You washed the plates, so it told itself this is a light load, and the one baked-on dish in the corner comes out still dirty.

Whirlpool draws the same line in slightly different words. Scrape excess food into the garbage or a disposer and remove bones, toothpicks and other hard items. Scrape before loading, and do not pre-rinse. And then it adds a consequence that pre-rinsing enthusiasts will not enjoy: pre-washing can contribute to etching, which is permanent damage to glassware and the subject of a section further down.

The trade nobody notices they are making

Go back to that filter table for a moment and read it as an exchange rather than a schedule. Washing dishes before loading them does extend the filter interval, all the way out to once a year. On the face of it that looks like a reward for diligence.

Look at what was traded. You have moved the work off a filter that takes two minutes under a tap once a month, and onto every plate, every bowl and every pan, by hand, every day of the year. In return you get a longer filter interval, a sensor that underestimates the load, and a documented contribution to etched glass. The three-tier distinction is worth keeping straight: scraping is required, rinsing is counterproductive, and washing before loading is a large amount of work for no benefit the machine needed and at least one real risk.

Toronto Hard Water Inside a Dishwasher

The City of Toronto publishes an annual drinking water analysis summary, and the 2025 edition reports hardness, expressed as calcium carbonate, averaging 119 mg/L across 119 samples, with a minimum of 115 and a maximum of 122. That is a remarkably narrow band, which means a Toronto household can treat the figure as a constant rather than a seasonal variable.

Health Canada's guideline technical document on operational parameters puts that number in context. It notes that hardness classifications differ between sources, and on the scale it reproduces, 100 to 150 mg/L is medium hard. It also observes that a hardness level of 80 to 100 mg/L provides an acceptable balance between corrosion and incrustation, that supplies above 200 mg/L are considered poor although they have been tolerated, and that hard water causes scaling of hot water pipes, boilers and other household appliances. The fraction responsible is carbonate hardness, which precipitates out when the water is heated, which is precisely what a dishwasher does to it.

Converting the number into the one the manual uses

Appliance manuals in North America do not use milligrams per litre. They use grains per gallon, and the conversion is published in the same Health Canada document: a grain per gallon of hardness is equivalent to 17.1 mg of calcium carbonate per litre. Toronto's 119 mg/L therefore works out to a little under seven grains per gallon.

That is the number that makes the Whirlpool guidance usable, because its scale is in grains. Soft is 0 to 4. Medium is 5 to 9. Hard is 10 to 14. At 15 or more the manual calls the water extremely hard, says it can damage the dishwasher, and recommends a water softener.

At about seven grains, Toronto sits in the middle of medium. The practical conclusion is a double negative that is genuinely useful: you do not need a water softener for your dishwasher in Toronto, and you also do not get to ignore hardness. The manual has a specific list for households without a softener, and all of it applies here. Use a commercial dishwasher cleaner monthly. Clean the filters monthly. Always use rinse aid. Use fresh detergent. And consider a detergent booster designed for dishwashers if filming persists.

Rinse aid is not optional on this water

Rinse aid gets treated as a luxury additive, and on medium-hard water it is closer to a requirement. Its job is to break the surface tension of the final rinse so the water sheets off rather than beading, which means the minerals leave with the water instead of drying in place as spots.

The Whirlpool dispenser holds 5 oz (150 mL) and lasts roughly one to three months depending on the setting. Raise the setting if calcium is building up on the dishes; lower it if you start seeing foam. The Bosch system has four levels with level 2 as the factory default, and the two directions do different jobs: a lower setting reduces streaking, a higher setting reduces water spots. On Toronto water, the factory default is a starting point to be adjusted rather than an answer, and the direction to move is usually up.

Detergent form matters too, and the manual is unusually direct about it. Quality tablets and packs reduce filming better than powder, liquid or gel detergents.

The spray arms are the second thing to check

Scale does not only land on dishes. The Bosch manual asks you to clean the spray arms regularly, because limescale and soil can block the nozzles and the bearings. Unscrew and remove the upper arm, pull the lower arm upward to release it, and rinse the outlet nozzles under running water.

Blocked nozzles are a direct and very common cause of the complaint that a dishwasher has stopped cleaning well, and the symptom is distinctive: the dishes in one part of the rack come out fine and the dishes in another part come out dirty, because a section of the spray pattern has gone missing. On medium-hard water this is the first thing to check after the filter, and holding a nozzle up to the light tells you the answer in a second.

Mineral residue inside appliances is a recurring Toronto theme rather than a dishwasher quirk. The washing machine on the other side of the house has the same problem for the same reason, and we have written about it in our guide to laundry room cleaning in Toronto, which covers scale and biofilm in a washer alongside dryer vent safety.

Cloudy Glasses: Film You Can Remove and Etching You Cannot

Upside-down drinking glasses drying on a stainless steel rack after a dishwasher cycle in soft kitchen light

Glasses that come out of the dishwasher permanently hazy are one of the most common complaints about the appliance, and they have two completely different causes with completely different outcomes. One is a mineral deposit sitting on the surface of the glass, which can be removed. The other is etching, which is the surface of the glass itself having been altered, and which cannot.

The Whirlpool manual gives a five-minute test that settles it before you spend any money. Soak the affected item in white vinegar for five minutes. If the cloudiness disappears, the cause is hard water and the deposit is removable. If the cloudiness is still there, it is etching, and the manual does not soften the verdict: if etching has occurred, the glassware is permanently damaged.

Doing that test first is the whole point. It is the difference between buying a rinse aid and adjusting a setting, and replacing a set of glasses that no product on any shelf will ever recover.

What actually causes etching

The manual names two contributors, and both are things people do deliberately in the belief that they are helping. The first is pre-washing dishes, which is the folklore from the section above showing up a second time with a different cost attached. The second is using the water-heating options when the incoming water is already at or above 120°F, which means the heat boost that exists to rescue a cold-water supply becomes a liability on a house whose water heater is set correctly.

The distinction between a deposit and an altered surface is exactly the same one that decides whether cloudy shower glass can be saved, and it is worth understanding once because it recurs all over a hard-water house. We took it apart in detail in why Toronto shower glass turns cloudy, including how to tell deposits from etching on a panel you cannot soak in vinegar.

Water Temperature Is a Setting You Control Outside the Machine

One of the more useful things in the Whirlpool manual is that it treats the dishwasher as the end of a system rather than the whole of it. For best dishwashing results, it says, water should be 120°F (49°C) as it enters the dishwasher. When the complaint is food soil left on dishes, it asks you to confirm the incoming water is at least 120°F. When the complaint is that sanitizing failed, it asks you to set the water heater to 120°F. And it gives one habit to adopt: run hot water at the nearest sink before starting a cycle.

That last instruction looks trivial and is not. The water sitting in the pipe between the heater and the dishwasher has been cooling to room temperature since the last time anyone used that line, and the first minutes of a cycle draw exactly that. Running the kitchen tap hot for a few seconds first pushes the cold slug out of the way and gives the machine the temperature its cycle was designed around.

It is also the step that matters most in a Toronto January, for a reason that is arithmetic rather than measurement: the heater is starting from colder mains water in winter than in July, so the same thermostat setting is working harder to hold the same output. If the sanitize indicator flashes rather than glows, or if winter is the season the dishes started coming out gritty, this is the first thing to test, and it costs nothing to test it.

Note the one direction the manual gives for the heat-boost options: use them only when the incoming water is below 120°F. If the supply is already there, the boost buys nothing and adds etching risk. The fix for a cold supply is the thermostat on the water heater, which is the one part of dishwasher performance that is not located in the kitchen at all.

Standing Water, Drains and Smells

Water left in the bottom of the tub at the end of a programme has a short diagnostic chain in both manuals, and neither of them suggests a product. The Bosch manual sends you to the filter system first and the drain pump second.

The drain pump procedure is the one genuinely hands-on job in this article. Disconnect the power. Remove the racks and the filter system. Scoop out the standing water. Remove the pump cover, clear any food debris or foreign objects from the impeller, and refit the cover until it clicks. The manual attaches a safety note that is worth taking literally: sharp debris such as glass fragments may be present, so this is a gloves-and-look-first job rather than a reach-in-blind one.

Whirlpool adds a second place to check that people rarely know exists. If the dishwasher drains poorly, check and clean the drain air gap, which is the small chrome cylinder on the countertop beside the faucet in many installations. It also recommends running a rinse cycle with a partial load if the machine is not used daily, which stops soil drying onto the filter between runs.

What the manuals do not say about odours

Neither manual contains a dedicated odour procedure, and that absence is informative rather than an oversight. There is no deodorizing step because there is no deodorizing problem; there is a drainage, filter or seal problem which presents as a smell.

Everything the two documents offer on the subject points back to the same four components: the filters, the spray arms, the door seals and drainage. Bosch's single explicit odour instruction is the one from earlier, to leave the door slightly ajar during long periods of non-use. A dishwasher that smells is not asking for a fragrance. It is reporting one of those four, and the reporting is accurate.

It is also worth ruling out the rest of the room before blaming the appliance, because a kitchen has several candidates and grease is a frequent one. Our guide to kitchen grease removal in Toronto covers the cabinet fronts, the range hood filter and the backsplash, which between them account for a good share of kitchen smells people attribute to the dishwasher.

Where Vinegar Fits, and Where It Does Not

The popular answer to every dishwasher question is vinegar, usually with baking soda, occasionally with citric acid. What makes this interesting is that the two manuals disagree with each other about it, and the disagreement is more useful than either answer would be alone.

Whirlpool sanctions a specific, bounded procedure. Remove all silverware and metal items. Put 2 cups (500 mL) of white vinegar in a glass or dishwasher-safe measuring cup on the lower rack. Run a Normal cycle with no detergent and the heat dry turned off. Then comes the caveat that the hack posts leave out: using it too often could damage your dishwasher.

What the same manual recommends monthly instead is a dishwasher cleaner: one tablet in the detergent dispenser, no detergent and no dishes, on a Normal cycle. Monthly habit, cleaner. Occasional corrective for mineral film, vinegar.

The Bosch manual does not mention vinegar anywhere. What it says instead is never use detergents containing chlorine and do not use bleach-based products, and for the tub it offers a method that needs no additive at all: remove heavy soiling with a damp cloth, add detergent, select the hottest programme and run it with no dishware in the machine. That is a monthly maintenance cycle using nothing you do not already own.

So the honest summary is three sentences. Vinegar is an occasional corrective for mineral film, not a routine, and not on every brand. A monthly habit should be either a dishwasher cleaner or a hot empty cycle. And neither one replaces pulling the filter or wiping the seal, because nothing poured into the tub ever reaches the inside of a fold of rubber at the edge of the door.

The rule that covers every brand, including the ones not consulted here: the method in your own manual beats the method in any article, this one included. The model number is on the edge of the door or inside the frame, and the manual is a search away.

A Realistic Dishwasher Routine for a Toronto Kitchen

Assembled from the two manuals and adjusted for medium-hard water, the whole job comes to a few minutes a month. Written out as intervals it looks like this.

After every cycle. Glance at the upper filter for debris, which is what the Bosch manual asks for, and wipe the door seal and the lower door edge dry with a cloth. Thirty seconds, and it is the half of the job that prevents rather than corrects.

Weekly. Wipe the seal properly, fingertip inside a damp cloth, right into the fold and around the whole perimeter, with a little dishwashing liquid. Dry it afterwards.

Monthly. Pull and rinse the filter assembly. Run a dishwasher cleaner tablet or a hot empty cycle. Hold the spray arm nozzles up to the light and rinse them if any are blocked. Check the rinse aid level.

Seasonally. Do the five-minute vinegar soak test on one cloudy glass if film has started appearing, and adjust the rinse aid setting upward rather than buying anything. Confirm the water heater is delivering 120°F. Clean the drain air gap if drainage has slowed.

Before a trip. Leave the door slightly ajar. In warm weather, turn off the water supply at the nearest point to the dishwasher. In freezing conditions the Bosch manual asks for an authorized service provider to winterize the machine, which matters far more for an unheated property or a cottage than for a city condo that stays at 20°C all winter.

Nothing on that list needs a specialist product, and nothing on it takes longer than the time people currently spend rinsing plates that did not need rinsing.

What a Cleaning Visit Covers and What Stays With You

Appliance interiors fall into an awkward gap in most people's expectations of a cleaning service, so it is worth being plain about the division of labour, because it is a real one and it runs along a clear line.

The mechanical half is straightforward to hand over. Pulling and rinsing the filter, checking and clearing the spray arm nozzles, cleaning the seal into the fold, the door edge and the exterior panel are all ordinary tasks for a thorough clean, and they are exactly the tasks that get skipped when nobody has been told the filter exists. They sit naturally inside a deep cleaning service rather than a standard weekly visit, because they are interval tasks rather than surface ones.

The other half cannot be delegated, and pretending otherwise would be dishonest. Which cycle gets selected, whether the sanitize option is used for the load that held raw chicken, whether the rinse aid is topped up, what the water heater thermostat is set to, and the decision to stop pre-rinsing are all household decisions made at the moment of use. A cleaner is not standing there when the door closes. If you want more context on where appliance work generally sits relative to a routine clean, our older piece on dishwasher efficiency covers the loading side of the same appliance.

Custom Maids has been cleaning Toronto homes for more than 48 years, and the products used on any job are the ones the client supplies rather than ones we bring. On a dishwasher that is an advantage rather than a logistical detail. Both manuals prohibit chlorine and bleach-based products near the interior and the seal, and when the cupboard is yours, you already know exactly what is going near a gasket that chlorine would ruin.

Sources and Research

The colonization figures come from Zupancic, Novak Babic, Zalar and Gunde-Cimerman, The Black Yeast Exophiala dermatitidis and Other Selected Opportunistic Human Fungal Pathogens Spread from Dishwashers to Kitchens, PLoS ONE 11(2): e0148166 (2016). It is the survey of thirty residential dishwashers that found fungi in twenty-five of them, recorded the per-site percentages for seals, side nozzles, doors and drains, measured counts on the seals of up to a million colony-forming units per square centimetre, and found Exophiala dermatitidis in kitchens with a dishwasher but in only one of the fourteen kitchens without one.

The sanitization standard is NSF/ANSI 184, and the 99.999% five-log bacteria reduction requirement, the 150°F final rinse temperature and the statement that performance is verified only on the sanitizing cycle are taken from NSF's page on residential dishwasher certification.

The filter removal procedure and its frequency table, the grains-per-gallon hardness scale, the without-a-softener list, the rinse aid capacity and adjustment directions, the tablets-versus-powder note, the 120°F incoming water requirement, the Sani Rinse temperatures of 135°F and 156°F, the drain air gap, the five-minute vinegar soak test for etching and the bounded 2-cup vinegar procedure are from the Whirlpool dishwasher user instructions. The instruction to check the filters after every cycle, the coarse and micro filter disassembly order, the spray arm and drain pump procedures, the prohibitions on chlorine detergents, bleach-based products, steam cleaners and abrasive sponges, the four rinse aid levels, the do-not-pre-rinse instruction with its sensor explanation, the hot empty cycle method and the door-ajar and winterizing advice are from the Bosch dishwasher use and care manual.

Toronto's water hardness, averaging 119 mg/L across 119 samples with a minimum of 115 and a maximum of 122, is from the City of Toronto 2025 drinking water analysis summary. The medium-hard classification for 100 to 150 mg/L, the conversion of 17.1 mg/L to one grain per gallon, the 80 to 100 mg/L corrosion-and-incrustation balance figure, the above-200 mg/L threshold and the statement that hard water scales household appliances are from Health Canada's guideline technical document on operational parameters in drinking water. The guidance that plates and utensils touched by raw food be washed in the dishwasher or in warm soapy water, the separate 5 mL to 750 mL bleach solution for surfaces and the note that children five and under produce less of the stomach acid that kills harmful bacteria are from Health Canada's safe food handling guidance for children ages five and under.

A Word from Custom Maids Toronto

(Sponsor of the Article)

For more than 48 years we have been cleaning homes across Toronto, and in that time kitchen appliances have changed almost beyond recognition. One thing about them has not changed at all: the parts that need attention are the parts that are easy to miss. A screen under the lower rack. A fold of rubber at the edge of a door.

We do not supply cleaning products, and our clients do. On a job like this one that is a genuine advantage rather than a piece of small print. Two manufacturer manuals rule out chlorine and bleach anywhere near a dishwasher interior, and when the products come out of your own cupboard, you already know precisely what is going near a gasket, which matters in a home with allergies, pets, young children or anyone sensitive to scent.

If the filter in your dishwasher has never been out, that is where to start, and it takes about two minutes. If you would rather have the interval work built into a regular clean, talk to Custom Maids Toronto about what that looks like.

Frequently Asked Questions

How often should I clean my dishwasher filter?

The Whirlpool frequency table runs from every two months to once a year depending on load count and whether you scrape or rinse, but the same manual elsewhere says monthly, and its hard-water guidance says monthly too. On Toronto's medium-hard water, monthly is the figure to use. Clean it sooner if there is visible soil on the upper filter or if the dishes feel gritty.

Does my dishwasher actually sanitize dishes?

Only on its sanitizing cycle, and only if the water gets hot enough. NSF/ANSI 184 requires a 99.999% reduction of bacteria and a final rinse of 150°F, and sanitization performance is verified only on that cycle. On a Whirlpool, Sani Rinse takes the final rinse to 156°F and lights a Sanitized indicator, which flashes instead if the cycle was interrupted or the water never got there.

Should I rinse dishes before loading the dishwasher?

No. Scrape off large food remnants and remove bones and toothpicks, then stop. Both manuals say not to pre-rinse, and the Bosch one explains why: rinsing too thoroughly makes the soil sensors select a lighter cycle, which leaves the stubborn residue behind. Whirlpool adds that pre-washing can contribute to permanent etching of glassware.

Is it safe to put vinegar in a dishwasher?

It depends on the brand, which is why reading your own manual beats reading advice. Whirlpool describes a bounded procedure using 2 cups of white vinegar in a glass measuring cup on the lower rack with no detergent and heat dry off, and then warns that using it too often could damage your dishwasher. The Bosch manual never mentions vinegar; it prohibits chlorine detergents and bleach-based products and offers a hot empty cycle instead.

Why are my glasses cloudy after they come out of the dishwasher?

There are two causes and one test. Soak the glass in white vinegar for five minutes. If the cloudiness disappears, it is a hard water deposit and the fix is rinse aid and settings. If it does not, it is etching, and the glassware is permanently damaged. Run the test before buying any product.

Does Toronto water need a softener for the dishwasher?

No. At an average of 119 mg/L, and using Health Canada's conversion of 17.1 mg/L to one grain per gallon, Toronto water is a little under seven grains, which is mid-range medium on the Whirlpool scale. A softener is recommended only at 15 grains or more. What does apply is the without-a-softener list: rinse aid every time, filters monthly, a dishwasher cleaner monthly and fresh detergent.

Why does my dishwasher smell?

Neither manual has an odour procedure, because a smell is a symptom of one of four things: the filters, the spray arms, the door seals or drainage. Work through them in that order. Bosch's only direct odour advice is to leave the door slightly ajar during long periods of non-use, which stops the cabinet staying warm and damp between cycles.

There is water sitting in the bottom of my dishwasher. What should I check?

The Bosch manual sends you to the filter system first and then the drain pump, where you disconnect the power, remove the racks and filters, scoop out the water, take off the pump cover and clear the impeller, with care because glass fragments may be present. Whirlpool adds the drain air gap, the small chrome cylinder on the counter next to the faucet in many installations.

What temperature should the water be when it reaches the dishwasher?

120°F, or 49°C. Whirlpool asks for that figure for best results, asks you to confirm it when food soil is being left behind, and asks you to set the water heater to it when sanitizing fails. Running the kitchen tap hot for a few seconds before starting the cycle pushes the cooled water out of the pipe, which matters most in winter.

Can a cleaning service clean the inside of my dishwasher?

The mechanical parts, yes: the filter, the spray arm nozzles, the seal and its fold, the door edge and the exterior. Those are interval tasks that sit naturally in a deep clean. What stays with the household is the cycle you select, the rinse aid, the water heater setting and the habit of scraping rather than rinsing.

Custom Maids

The GTA’s First and Original

Home Cleaning Service

Serving Toronto, Vaughan, Markham and Richmond Hill

Since 1978, Custom Maids has been a trusted presence in the GTA. Over five decades we have cleaned more than five million homes and continue to set the standard for professional home cleaning in the Greater Toronto Area.

Get Social With Us

2026 marks the 48th anniversary of the founding of Custom Maids. With decades of experience behind us, we continue to serve thousands of households in Toronto, Vaughan, Richmond Hill and Markham with the same care and attention that built our reputation. Our story is written quietly, in the homes we clean and the trust we earn every day.

Born in the GTA.  Canadian-Owned.  Trusted Since 1978.

bottom of page