top of page

Butcher Block Cleaning in Toronto: Oiling, Cutting Board Safety and Winter Cracking

Writer: Desmond Breau
Desmond Breau
Nov 3
21 min read

A wood counter is the only surface in your kitchen that is still moving. Quartz does not care what the weather is doing outside. Granite does not shrink in February. Wood exchanges moisture with the air around it every day it is in the house, swelling slightly in a humid August and tightening in a dry January, and that single difference is why a cleaning routine that keeps a stone counter flawless will quietly destroy a butcher block in two or three Toronto winters.

Wood is also the surface people get the most contradictory advice about. The maker of a premium hardwood block says to oil it at least once a month. The maker of a popular solid-wood worktop says once a year. A federal conservation laboratory that has spent decades keeping wooden objects intact says that oiling does not do the thing almost everyone believes it does. All three are telling the truth about different problems, and the space between them is where most wood counters get damaged.

This guide pulls apart the three jobs that usually get muddled into one - cleaning, food safety, and protecting the wood itself - and gives you a routine for each. It covers butcher block counters, wooden cutting boards, wooden utensils and bowls, and the two things a Toronto house does to wood that a generic care guide will never mention: hard tap water, and a heating season that pulls the moisture out of every board in the kitchen.

Bright Toronto kitchen with grey cabinets, butcher block countertops and stainless steel appliances

Why wood behaves differently from every other counter

Wood is hygroscopic. It absorbs moisture from humid air and releases it into dry air, and as its moisture content changes, so does its size. The Canadian Conservation Institute, the federal body responsible for preserving wooden objects in Canadian collections, puts the mechanism plainly: a change in relative humidity changes the moisture content of organic materials such as wood, and if the wood can move freely there is no problem. The damage happens when it cannot.

A butcher block counter is the definition of wood that cannot move freely. It is dozens of narrow strips glued edge to edge, then screwed down to a cabinet frame. The Conservation Institute specifically flags wood held by bolts or screws passing through both sides of a single plank as highly sensitive to humidity swings, and notes that wood and wood assemblies under fluctuating humidity may crack, split, delaminate or distort permanently. Your counter has both failure modes built in: glue lines that can open, and fasteners that stop the wood from moving.

The second thing to understand is that you are almost never cleaning wood. You are cleaning the finish on top of it - an oil film, a hardwax, or a varnish. The Conservation Institute makes the point that roughly half the value of both new and old furniture sits in the finish rather than the wood, and on a kitchen counter that film is also the moisture barrier that keeps water out of the glue joints. Every cleaning decision you make is really a decision about that film.

This is the opposite of the problem a stone counter presents. If you have both in the same kitchen, our guide to quartz countertop cleaning in Toronto covers a surface where the care rules conflict for completely different reasons, and the granite countertop care guide covers the sealed-stone middle ground. Wood is the outlier, and it needs its own routine.

Daily cleaning: what wood actually needs

The daily routine for wood is shorter than most people expect, and the discipline is entirely about water. Damp, never wet. Dry immediately, never air-dry.

The routine that works

Scrape before you wash. A bench scraper or a stiff spatula pushed across the surface takes off crumbs, trimmings and dried food without introducing any water at all. The hardwood block manufacturer recommends doing this several times a day as needed and describes it as part of keeping the surface clean and sanitary, which is the right way to think about it - most of what is on a cutting surface is solid, and solids do not need a wet cloth.

Then wash with mild soap and water, rinse the soap off, and dry the surface thoroughly. That three-step sequence is the manufacturer's own instruction, and the rinse step is the one people skip. Soap residue left on an oiled surface dulls it and attracts dust. The worktop manufacturer gives the same basic answer from the other direction: for daily cleaning, ordinary washing-up detergent, soap or water is all that is needed.

Health Canada's household food safety guidance adds the frequency: wash countertops with warm soapy water after preparing each food item, not once at the end of the evening. On a wood counter that is easier than it sounds, because a damp cloth and a dry cloth in sequence takes about fifteen seconds.

For wooden furniture, bowls and utensils rather than counters, the Conservation Institute's method is gentler still: dust regularly with a slightly dampened cloth, then buff with a dry, soft cloth. It also warns that unfinished wood should not be wet-cleaned at all - which covers raw wooden salad bowls, spoons and the undersides of a lot of boards.

What should never touch a wood surface

The dishwasher. This is the single fastest way to ruin a wooden board, and both the manufacturer and the food safety researchers agree without qualification: never put wood cutting boards in a dishwasher, and a dishwasher would ruin a wood board. The combination of prolonged soaking, heat and detergent swells the wood, softens it and attacks the glue lines all at once. If you want to know what the machine is actually good for, our guide to getting the most out of a dishwasher covers how to get the best out of the machine itself.

Harsh detergents and all-purpose sprays. The block manufacturer says not to wash cutting boards with harsh detergents of any kind. The worktop manufacturer is blunter still: never use chemicals to clean the worktop. Wood absorbs, and whatever you spray on it does not evaporate off the way it does from stone or laminate.

Standing water and wet food. Do not let wet meats or liquids sit on the surface for long periods. The manufacturer is explicit about why: it causes swelling, softening and weakened glue joints. A chicken thawing on a block, a wet dish rack, a puddle under a kettle - all of them do the same damage over months.

Abrasives on the cutting surface. No steel brush, no scouring pad. Scratches in an oiled surface are not cosmetic; they are breaches in the moisture barrier.

Build-up polishes and furniture sprays. The Conservation Institute is unusually direct on this point: some commercially available products actually do more harm than good, and some polishes leave residues that produce unsightly build-up and can affect finishes. A silicone furniture spray on a butcher block is a problem you will be sanding off later.

This is one of the places where the way we work is genuinely an advantage rather than a talking point. Custom Maids does not bring cleaning products into your home - you supply them. On a wood counter, which keeps a record of everything it absorbs, that means the only things your block ever meets are the ones you chose.

Cutting boards and food safety: what the research actually found

The belief that plastic boards are more hygienic than wooden ones is one of the most durable pieces of kitchen folklore in North America, and it has been tested directly.

The 1994 experiment

A study published in the Journal of Food Protection in 1994 took four plastic polymers, a hard rubber and nine hardwoods, cut them into five-centimetre square blocks, and deliberately contaminated them. The organisms were Escherichia coli, including the O157:H7 strain, Listeria innocua, Listeria monocytogenes and Salmonella typhimurium, suspended either in nutrient broth or in chicken juice. The researchers then tried to recover the bacteria at intervals from a few minutes out to roughly twelve hours, either by soaking the block or by pressing it onto nutrient agar.

The results ran against expectation. Recoveries from the wooden blocks were generally lower than from the plastic blocks, and that held for both new and used boards. The gap widened as the holding time increased. Bacteria left overnight on plastic multiplied; the clean wooden blocks usually absorbed the entire inoculum within three to ten minutes, which the authors identified as the likely reason so little could be recovered from them afterwards.

Wood, in other words, is not a sterile surface. It is an absorbent one, and the bacteria that go into it do not come back out onto your next tomato - they die in there as the board dries. That is a meaningfully different safety mechanism from the one most people assume they are using.

What that does and does not license

It does not make wood the right board for everything. Food safety researchers at North Carolina State University, discussing that same body of work, land on a split recommendation: plastic boards are easier to sanitize, and plastic can go through a dishwasher where the high-temperature wash does the sanitizing for you. Dense hardwoods such as maple trap bacteria in their fine grain where the bacteria die as the board dries, while softer woods with larger grain split into grooves that hold moisture and bacteria. Their practical conclusion is plastic for raw meat, wood for produce and ready-to-eat food.

That lines up with Health Canada's own guidance, which is not about the material at all: cut and prepare raw meat, fish and poultry on a separate cutting board from the one you use for everything else, and do not reuse a utensil that has touched raw food until it has been cleaned either in the dishwasher or in warm, soapy water. The block manufacturer adds one wood-specific caution to it - do not cut fish or poultry on a wooden surface unless the moisture barrier is intact, and clean the surface thoroughly afterwards.

Put together, the setup that satisfies every one of those sources costs almost nothing: one good wooden board or block for vegetables, bread, cheese and fruit, and one cheap plastic board reserved for raw meat and poultry that goes straight into the dishwasher after use. Colour-code them if more than one person cooks. The wooden board never meets raw chicken, so the question of whether wood can be sanitized well enough for raw chicken never has to be answered.

If you do want to disinfect a kitchen surface, Health Canada's household sanitizing solution is five millilitres of household bleach - about a teaspoon - in 750 millilitres of water, mixed in a labelled spray bottle. On wood, use it sparingly, wipe it rather than flooding it, and dry the surface immediately afterwards, because the absorption that makes wood perform well in the laboratory also means it will take up whatever you leave sitting on it.

When a board is finished

A board with a few knife marks is working as designed. A board with many deep grooves is a different object. The NC State researchers make the replacement test simple: the more grooves there are and the larger they are, the more space there is for moisture and bacteria to sit, and deep grooves are a reason to retire a board.

You can push that day a long way out. The manufacturer's advice is to avoid cutting in the same spot repeatedly, to rotate a reversible board so both faces wear evenly, and to sand minor scratches out with 200-grit paper worked along the grain rather than across it. It also stresses keeping the original edge bevel intact, because a squared-off edge is where splitting and chipping start. Re-oil after any sanding.

Three things mean a board or a block is past saving rather than past sanding: a glue line you can catch a fingernail in, a split that runs through the full thickness, and a smell that survives a proper scrape, wash and complete dry. The last one usually means something has gone into a crack rather than onto the surface.

Fresh cucumbers and tomatoes being sliced on a wooden chopping board in a Toronto kitchen

Oiling: the advice that contradicts itself

Search for how often to oil a butcher block and you will get two answers that are twelve times apart. Both come from manufacturers, both are correct, and neither one is the answer to the question most people are actually asking.

What the manufacturers say

The hardwood block maker's schedule is a minimum of once a month, depending on use and household conditions. The method is to apply the oil, let it soak in overnight, then wipe off the excess, with an optional board cream afterwards for extra protection, also left to penetrate overnight. Oil only a clean, dry surface. Its own test for timing is pleasingly low-tech: a dry appearance means it is time to oil. It also warns against over-oiling, which leaves a tacky film rather than a protected one.

The solid-wood worktop maker's schedule, for the same material in a different role, is once a year or as needed. That worktop arrives pre-treated with a single factory coat, and the installation instructions call for sanding along the grain, wiping the dust off, and then repeating the oil treatment three times with about a day between coats so each one can dry - thin coats, roughly fifteen minutes to soak, surplus wiped off with a soft cloth every time. After that, annual maintenance, with one exception that matters enormously: the areas where the worktop may dry out, such as around the sink and the hob, should be treated often.

The two schedules are not in conflict once you see what they are measuring. An end-grain block that gets scraped and washed every day loses its oil film constantly. A sealed worktop that is wiped down and never cut on loses almost none. Oiling frequency follows how much film you are removing, not the calendar - which is why the manufacturer's dry-appearance test beats any interval you could write down.

What oil cannot do

Here is the part that almost no cleaning guide mentions. The Canadian Conservation Institute's position, after decades of keeping wooden objects intact in Canadian buildings, is that wood does not need to be fed, and that no amount of oil or other material will keep wood from drying out if the humidity level is too low.

That is worth reading twice, because it reframes the whole ritual. Oil is a surface moisture barrier. It slows water going in and slows water coming out, and it is genuinely useful for both. What it does not do is hold moisture inside the wood against dry air. If the air in your kitchen is dry enough to shrink a counter, oiling it monthly will not stop that - it will only make the surface look better while it happens.

Which means the most important thing you can do for a wood counter in a Toronto winter is not a cleaning task at all.

A schedule that satisfies both

Oil on the surface's own signal rather than on a date: when the colour looks dry and chalky, or when water stops sitting on the surface and starts darkening the wood quickly instead. Oil the ends of the run nearest the sink and the stove noticeably more often than the middle, because those are the zones the worktop maker singles out. Keep the coats thin, give them a long soak - overnight if you can - and wipe off every bit of surplus, because over-oiling is a real failure mode and not just waste.

Use food-grade mineral oil, or the branded oil and cream the maker of your block sells; those products exist for exactly this and the instructions above are written for them. Kitchen cooking oils are a poor substitute: olive, canola and the rest are not drying oils, and left in wood they tend to develop an off smell rather than cure into a film. For wooden furniture and bowls rather than counters, the Conservation Institute suggests a micro-crystalline wax applied once a year, only on the surfaces people actually handle, taking care not to let it build up around metal fittings.

Water is the real enemy, and Toronto water leaves a mark

Modern kitchen sink beside a crock of wooden utensils, the wettest zone on any wood countertop

Almost every wood counter that fails in a Toronto kitchen fails because of water, and almost always in the same metre of counter: the run beside the sink.

The sink zone

Water does two separate things to wood. On the finish, a spill left to dry leaves a cloudy white patch - the Conservation Institute's description of the most common water damage on a wooden surface. Underneath the finish, prolonged wetting swells the wood, softens it and weakens the glue joints, which is the manufacturer's own warning about letting liquids sit.

The fix is a habit rather than a product. Dry the counter after washing instead of letting it air-dry. Keep a dish rack on a tray, or on the sink itself, rather than directly on the wood - a rack sitting on an oiled surface holds a thin film of water against it for an hour at a time, every day. Wipe the splash line behind the taps, which is the strip people never think of as a wet area. And treat the sink end of the run with oil more often than the rest, as the worktop instructions specifically recommend.

One source of wetting is genuinely invisible, and it is worth checking once. The worktop manufacturer's installation instructions call for a diffusion barrier on the underside of any wood worktop fitted above a dishwasher, washing machine or oven, because steam rises out of the appliance into the underside of the counter where nobody ever looks. If your block sits over a dishwasher and you have ever wondered why it cups or darkens on that one section, start there.

Hard water film and white rings

Toronto adds a complication that a generic wood care guide will not mention. The City of Toronto's 2025 Drinking Water Analysis Summary reports hardness averaging 119 milligrams per litre as calcium carbonate across 119 samples, ranging from 115 to 122, against a listed aesthetic objective of 80 to 100 milligrams per litre. Our tap water sits above the range the city itself flags as desirable, and every drop that dries on a surface leaves that mineral behind.

On glass, that mineral is obvious - it is the same process behind cloudy Toronto shower glass. On oiled wood it is subtler and more annoying: a dull grey haze across the surface that looks like the oil has failed, plus pale rings wherever a wet glass or pot has stood. The mineral is sitting on top of the finish, and it goes with a damp cloth and immediate drying while it is fresh. Left for weeks it bonds into the film and comes off only with the oil, which means re-oiling.

This is also why drying matters more here than it would in a soft-water city. Air-drying a wood counter in Toronto does not just leave water on the wood for longer - it guarantees a mineral deposit every single time.

Winter in a Toronto house: cracks, gaps and glue lines

Between December and March, the air inside a heated Toronto house becomes the most hostile environment a wood counter will ever experience, and nothing in a cleaning cupboard can help with it.

The Conservation Institute puts a number on how far it can go: winter heating without humidification can drive indoor relative humidity down to as low as five per cent at a room temperature of 21 degrees. At that level it describes a high risk of furniture cracking - with one important qualification, which is that the low humidity has to persist long enough for the piece to respond fully. Wood takes anywhere from days to months to come into equilibrium with the air around it, depending on thickness and coatings, which is why the Institute's recommendation is to keep any low-humidity period short rather than to aim for a perfect number.

It also notes that most objects in Canada have experienced swings of at least twenty percentage points of relative humidity, and that under those fluctuations wood assemblies may crack, split, delaminate or distort permanently. Small swings into high humidity can crush joints invisibly, which then makes splitting more likely when the humidity drops again. A butcher block counter - many glued strips, screwed down through its thickness - is close to the worst-case geometry the Institute describes.

The practical conclusion is unglamorous. The most effective maintenance for a wood counter over a Toronto winter is keeping the indoor humidity from collapsing: running the humidifier if the house has one, not venting the kitchen harder than necessary on the coldest days, and putting an inexpensive hygrometer somewhere in the kitchen so you can actually see what the air is doing. A hygrometer tells you about a coming problem weeks before a crack does.

One reassurance. A hairline gap that opens along a glue line in January and closes again by July is normal seasonal movement, not a defect - the same physics that makes Toronto hardwood floors gap in winter and tighten in summer. A gap that does not close, or one that keeps widening year over year, is permanent and worth having looked at.

Stains, scorch marks and knife scars

Wood is the one counter material where most marks are in the finish rather than in the surface, which is good news: a finish can be renewed, and stone cannot.

White rings and cloudy patches. On an oiled or hardwax surface, these are usually moisture sitting in the film. Dry the area thoroughly, leave it a day, and if the haze remains, a light sanding along the grain with fine paper followed by a fresh thin coat of oil will take it out. On a varnished or lacquered worktop, white blooming is damage to the coating itself and sanding will make it worse - that is a refinisher's job.

Food stains. Beet juice, turmeric, berries and red wine all go into wood rather than onto it, so speed is the whole technique. Blot immediately, wash with mild soap, rinse, dry. A stain that has already set usually comes out with sanding rather than with any cleaner, which is why the manufacturer's 200-grit-along-the-grain instruction is the real stain removal method for wood.

Scorch marks. Nothing cleans a scorch out. Heat has charred the wood fibre, and sanding is the only route - fine paper, along the grain, keeping the edge bevel, then re-oil. Use a trivet and treat this as prevention rather than cure.

Odours. Garlic, onion and fish smells sit in the top fraction of a millimetre of wood. The full scrape, wash, rinse and complete dry cycle clears nearly all of them. If a smell survives that, something has gone into a crack or an open glue line and the board is telling you about structural damage rather than a cleaning problem.

Two cautions on bigger interventions, both from the Conservation Institute: stripping wooden furniture is not recommended, and anything needing extensive repair or cleaning should go to a conservator or professional refinisher rather than being experimented on. The same logic applies to a counter you like. And if the marks you are fighting are actually grease rather than water or food dye - common on the run beside a range - our guide to kitchen grease removal in Toronto covers the surrounding cabinets and backsplash, which are usually worse than the counter itself.

What a cleaning visit should and should not do to your wood

Wood is the surface in a house where a well-meaning cleaning routine does the most damage, because the damage is invisible for a long time and then permanent.

What a visit should do: scrape and crumb the surface dry first, wipe with a damp cloth and the mild soap you keep for it, rinse the soap off, then dry the whole surface with a second cloth. Lift the dish rack and wipe underneath it. Never leave a wet cloth lying on a block, and never leave the surface to air-dry.

What a visit should not do: spray an all-purpose cleaner on it, use an abrasive pad, flood the sink-adjacent run with water, or oil it unprompted. Oiling is a finish decision with a product choice attached, and it belongs to you rather than to whoever is cleaning that week.

Two things make this easier to get right. The first is simply telling your cleaner which boards are wood and which board is the plastic one reserved for raw meat - a thirty-second conversation that prevents the most common mistake. The second is that Custom Maids does not supply cleaning products; you do. Nothing arrives in a van and meets your butcher block without your having picked it, which matters far more on an absorbent surface than on tile. Across 48 years of cleaning Toronto homes, the wood we have seen ruined was almost always ruined by water and time, not by the wrong spray. You can read how we approach a regular house cleaning visit if you want the detail.

Sources and Research

The food safety guidance in this article comes from Health Canada's Safe food handling in the home, which supplies the separate-cutting-board rule for raw meat, fish and poultry, the instruction to wash countertops with warm soapy water after preparing each food item, the rule against reusing a utensil that has touched raw food before it is cleaned, and the household sanitizing solution of 5 mL of bleach in 750 mL of water.

The comparison between wood and plastic boards rests on Ak, Cliver and Kaspar, Cutting Boards of Plastic and Wood Contaminated Experimentally with Bacteria, Journal of Food Protection, 1994, volume 57, issue 1, pages 16 to 22, which tested four plastic polymers, a hard rubber and nine hardwoods against E. coli O157:H7, Listeria and Salmonella and reported lower recoveries from wood along with absorption of the whole inoculum within three to ten minutes. The split recommendation of plastic for raw meat and wood for produce, and the groove-based replacement test, come from North Carolina State University's summary of cutting board food safety research.

The wood behaviour, humidity and finish care material comes from two Canadian Conservation Institute publications: Agent of deterioration: incorrect relative humidity, the source for the five per cent indoor humidity figure at 21 degrees, the cracking and delamination risk, and the sensitivity of screwed and glued assemblies; and Basic care of furniture and objects made of wood, the source for the dusting method, the warning about build-up polishes, the advice against stripping, and the statement that no amount of oil will keep wood from drying out if the humidity is too low.

The two conflicting oiling schedules are quoted from the manufacturers themselves: care and maintenance instructions for hardwood blocks, which specifies a minimum of monthly oiling, the overnight soak, the no-dishwasher rule and the 200-grit sanding method; and the HAMMARP solid wood countertop care instructions, which specify three coats at installation, annual re-oiling, frequent treatment around the sink and hob, and a diffusion barrier above a dishwasher or washing machine. Toronto's water hardness figures are from the City of Toronto's 2025 Drinking Water Analysis Summary.

A Word from Custom Maids Toronto

(Sponsor of the Article)

Custom Maids has been cleaning Toronto homes for more than 48 years, which is long enough to have watched a great many butcher blocks go cloudy, cup beside a sink, or open along a glue line in a February cold snap. Wood is unforgiving of routine, and routine is exactly what a cleaning service brings into a house.

We work differently from most services in one respect that matters more on wood than anywhere else: we do not supply the cleaning products. You do. Whether that is a single mild soap, a fragrance-free line because someone in the house reacts to scent, or the specific oil your block manufacturer recommends, the only products that touch your surfaces are the ones you chose - and on a material that absorbs and keeps what it meets, that control is worth having.

If you would like a team that treats a wood counter as a wood counter rather than as another wipeable surface, get in touch with Custom Maids Toronto and tell us what is in your kitchen.

Frequently Asked Questions

Can I put a wooden cutting board in the dishwasher?

No, and this is the rare question with no nuance in it. The block manufacturer says never, and the food safety researchers say a dishwasher would ruin a wood board. Prolonged soaking, heat and detergent together swell the wood, soften it and attack the glue lines. Wash it by hand with mild soap, rinse the soap off, and dry it immediately.

How often should I oil my butcher block?

The honest answer is on its own signal rather than on a schedule. One manufacturer says at least monthly for a working block; another says once a year for a solid wood worktop. Both are right for their own situation, because oiling frequency follows how much film you remove. Use the manufacturer's test: a dry appearance means it is time to oil, and the sink and stove ends will always need it sooner than the middle.

Are wooden cutting boards less hygienic than plastic ones?

Not according to the research. In a 1994 Journal of Food Protection study, bacterial recoveries from wooden blocks were generally lower than from plastic ones for both new and used boards, and clean wood absorbed the entire contaminating dose within three to ten minutes. Plastic is still easier to sanitize because it can go in a dishwasher, which is why the standard recommendation is plastic for raw meat and wood for produce and ready-to-eat food.

What should I cut raw chicken on?

A separate board from everything else, which is Health Canada's rule regardless of material, and in practice a plastic one that can be run through the dishwasher. If you only have a wooden board, the manufacturer's caution is to cut poultry on it only if the moisture barrier is intact and to clean it thoroughly afterwards - but a second cheap plastic board removes the question entirely.

Can I use vinegar or an all-purpose spray on butcher block?

It is not worth the risk on a wood surface. One manufacturer says not to use harsh detergents of any kind; the other says never to use chemicals on the worktop at all. Mild soap, a rinse and a thorough dry handles ordinary kitchen soil, and Health Canada's dilute bleach solution handles disinfection if you need it - used sparingly and dried off at once.

A gap opened along a glue line this winter. Is my counter ruined?

Probably not. Heated indoor air in a Canadian winter can fall to as low as five per cent relative humidity at normal room temperature, and wood shrinks as it loses moisture to that air. A hairline gap that opens in January and closes by summer is seasonal movement. A gap that does not close, keeps widening year over year, or lets you catch a fingernail in it is permanent and worth having looked at.

Will oiling my block stop it cracking in winter?

No, and this is the most common misconception about wood care. The Canadian Conservation Institute states that no amount of oil or other material will keep wood from drying out if the humidity level is too low. Oil is a surface moisture barrier and it is worth maintaining, but the thing that prevents winter cracking is indoor humidity, not a bottle.

Why does my wood counter look hazy even after I clean it?

In Toronto, usually hard water. City testing put water hardness at an average of 119 milligrams per litre as calcium carbonate in 2025, above the 80 to 100 range listed as the aesthetic objective, so every drop that air-dries leaves mineral behind. A damp cloth and immediate drying lifts it while it is fresh; once it has bonded into the oil film, the haze comes off only when the oil is renewed.

Can I sand a scorch mark or a stain out myself?

Usually yes, on an oiled block. Use fine paper - the manufacturer specifies 200 grit - work along the grain rather than across it, keep the original edge bevel intact, and re-oil the sanded area afterwards. On a varnished or lacquered worktop, stop: sanding through a coating creates a much larger problem, and that is a refinisher's job.

Is a wood counter a mistake beside a sink?

Not a mistake, but it is the hardest-working section and it needs the most attention. Treat the sink end with oil more often than the rest, keep the dish rack on a tray rather than on the wood, dry the surface after washing instead of letting it air-dry, and check that any run installed above a dishwasher or washing machine has a diffusion barrier on its underside, which the worktop instructions call for.

Custom Maids

The GTA’s First and Original

Home Cleaning Service

Serving Toronto, Vaughan, Markham and Richmond Hill

Since 1978, Custom Maids has been a trusted presence in the GTA. Over five decades we have cleaned more than five million homes and continue to set the standard for professional home cleaning in the Greater Toronto Area.

Get Social With Us

2026 marks the 48th anniversary of the founding of Custom Maids. With decades of experience behind us, we continue to serve thousands of households in Toronto, Vaughan, Richmond Hill and Markham with the same care and attention that built our reputation. Our story is written quietly, in the homes we clean and the trust we earn every day.

Born in the GTA.  Canadian-Owned.  Trusted Since 1978.

bottom of page